Posted on November 1, 2018
Feeder Clamp – Upon Just What Basis Is It Best To Decide On..
Grounding exterior cables is equally as important as selecting the best cables for the television or Internet system. Grounding can prevent shocks from lightning strikes and surges from shooting across your coaxial cable and into the back of your television or Internet system. It is also not very difficult: anyone capable of connecting 1/2” Superflex RF Coaxial Cable can ground that same cable to an pre-existing electrical ground with little trouble.
Any television system with wires running outdoors should ground them. Attach the grounding block to your house, somewhere near where the coaxial cable will come in. A grounding block will have at the very least two screw holes; drill holes for every, then secure the block for the wall with the included screws.
Disconnect the coaxial cable from your splitter and hook it up to 1 side of the grounding block. You can do this simply by twisting the end until it comes loose. Lightly coat the ports on the grounding block with the silicone grease. This will aid in weatherproofing the ports. Perform the same for just about any open ports on the coaxial splitter.
Connect a brand new RG-6 coaxial cable to the point on the splitter where the previous cable was disconnected. Then attach another end from the cable towards the other side of the grounding block. Coaxial cables attach by inserting the pin from the center of the cable in to the pin-sized hole on the port, then twisting the cable until it secures in place.
Attach the grounding wire to the grounding screw on the grounding block. Loop the wire around the screw and twist the screw in up until the wire is secure. Then run the wire to the electrical ground and attach the wire there in a similar manner. If no screw is available, twist the end from the cable across the ground as tightly as you can; crimping with pliers if required.
Before I recieve into why and how you need to ground your antenna, I needed to let you know I am just not an electrician. I’m a DIY weekend warrior that depends on Google search-fu to figure out how to do household repairs and installs.
For just about any engineers or electricians that drop by, I welcome any critiques or corrections within the comments. Accuracy is really important in my opinion, and i also appreciate any corrections or adjustments you can offer.
That said, years of working in enterprise architecture cause me to a bit of a stickler for standards and practices. In case you are too, you may want to take a look at Article 810 in the National Electric Code. It covers each of the codes and standards for installing the cabling for TV and radio transmitters.
However, in case you are like lots of people, you’d rather hit your thumb repeatedly with a hammer than suffer through technical manuals. If so, I’ll do my advisable to take you step-by-step through a few things i did after looking on the code.
Below is really a picture describing just what we are going to do. It illustrates the best way to ground your antenna by connecting it in your house’s ground wire. Notice you must not only ground the Coaxial Cable Grounding Kit, but the antenna mast as well.
Grounding an antenna isn’t hard to accomplish yourself, but it shouldn’t be expensive to get a professional emerge and do that for you personally. In order to attempt this, below are are definitely the steps I took to recreate what exactly is essentially depicted within the diagram.
Cable installation basics. Install equipment and cabling in a neat and workmanlike manner [820.24]. You will find the industry practices described in ANSI/NECA/BICSI 568, Standard for Installing Commercial Building Telecommunications Cabling.
Exposed cables must be maintained by the structural aspects of the property to stop cable damage because of normal building use. Secure cables with straps, staples, hangers, or similar fittings designed and fmpuqh so as not to damage the cable.
Cables run parallel to framing members or furring strips must be protected where they could be penetrated by nails or screws. To provide this protection, you have two options. Install the cables a minimum of 1¼ inches through the nearest side of the framing member or furring strips.
Protect the Feeder Clamp having a 1/16-inch-thick steel plate Wiring support rules for coaxial cables could be a little tricky. Make sure you know where and when independent support wires should be used. You need to securely fasten raceways that contain coaxial cables in position. Don’t use ceiling-support wires or the ceiling grid to aid raceways or cables. It is possible to, however, support raceways and cables with independent support wires attached to the suspended ceiling.